MANUAL FOR A BST40 CARB MANUALS
MANUAL FOR A BST40 CARB INSTALL

This website is not maintained by KTM-Sportmotorcycle AG or KTM-Sportmotorcycle UK Ltd.KTM Products and the corresponding article numbers that KTM-Sportmotorcycle AG recommends for a particular application may change from time to time. Never change main or pilot jets to try and correct a mid-range problem. Once having made a change its back to the middle clip position and start all over again.Īn inability to tune out a problem in the mid range will indicate that the needle profile is not matched to your engine or a slide change may be required.

MANUAL FOR A BST40 CARB INSTALL

If improvements appear in one direction of adjustment but perfection is not achieved whilst having reached the end clip on the needle, then you will need to install a richer or leaner needle if available or else a corresponding needle jet. Generally if you have the right profile needle for your engine, a difference in performance and response can be detected by raising and lowering the needle. Mark the throttle twist grip and housing with a white out pen to identify when your slide is at ¼, ½, and ¾ opening, this will help you identify any particular problem areas and also keep you operating in the desired testing areas. Never drill jets and do remember that most aftermarket jets do not flow correctly. We don’t do returns on jets so maybe buy one bigger and one smaller to determine which way you need to go before then buying a selection in the correct direction (richer of leaner). Don’t give up half way through this process thinking you’ve got it right before reaching the limit, otherwise you may will be robbing yourself of a surprising amount of horse power!ĭo a plug check to be sure you’re not too lean when finished, job done. If you notice an improvement in one direction, keep changing to the next jet size in that direction till the improvement stops and she drops off the perch, then go back one. The performance changes can be detected at wide open throttle in low gears- we do not recommend the operation of motorcycles over the speed limit.Ĭhange and test with the next size jet both up or down to determine weather an improvement can be obtained and in what direction. Some engines will actually have two size jets that may fall within the 1-3 spec in which case see which feels better when riding, generally the richer one.Īt wide open throttle only the main jet is working so these are also very easy to tune with a few jets and a bit of spare time. Remember if you don’t wait 10 seconds for the engine to catch up every half turn at a very slow idle this tuning process will not work. Nothing else other than the pilot jet has an effect at idle. If the jet is wrong, either having no stumble in one direction or the centre point being out of the 1-3 range this will let you know that a jet change is required and weather you need to order richer or leaner jets. Then count the turns from this point to bottoming out, if you take less than 3 and more than 1 complete turns to achieve bottom, the jet is correct and you simply wind back to the centre point. Wind back ½ the number of counted turns to the centre point. Follow this with 1/2 turn checks winding in one direction every 10 seconds till the engine starts to stumble, at this point then wind back in the opposite direction counting your half turns till it stumbles again.

With your idle circuit, start at 1 1/2 to 2 turns out on the mixture screw and then wind your idle screw back to give a very slow idle whilst at operating engine temp with the bike upright. Here’s our simple outline for basic tuning to get you started. If at all in doubt, see your local tuning shop. Remember the tuning order is – idle circuit, then main jet and then finally mid range. Please positively identify your jet type in the jets section, as all jet sales are final with no refunds. Order required jets as your checks tell you. This is perhaps one of the best written book on carb tuning, just ignore the accelerator pump section if using a non pumper carb and remember that the mixture screw is an air screw where as on carbs with the screw located behind the bowl it will be a fuel screw in which case winding out is to make richer not leaner.īy following the procedures in the book you will determine if jets need changing and in what direction. We recommend you down load the HSR tuning books for Harley Davidson.

MANUAL FOR A BST40 CARB MANUALS

For tuning procedures we have a number of manuals available to the left.

Manual for a bst40 carb